Posts Tagged buttonhole height compensation plate
My lovely ginger boy, Henry, has had to have a trip to the V….E…..T.
He’s normally a big boy but was looking skinny, always looking for food and his back legs seemed a bit weak.
Anyway, a blood test, a blood pressure check and couple of hundred euros later, it turns out he has hypertension caused, probably, by some kidney problems. Who would have thought such laid back animals as domestic cats could get hypertension? Anyway, he now has to have two different medicines administered orally with a syringe every day. At the moment I’m keeping him in overnight then putting the medicine on a bit of tuna first thing so he’s hungry enough to eat it. I’ve tried administering it directly down his throat but he chokes and spits and generally makes a huge fuss and the medicine often ends up on the floor. The medicine for the hypertension will be for life so if anybody knows how to do this without causing stress – and thus more hypertension – I would be grateful for any tips.
The second ginger in my life is my pair of Ginger Jeans. Yes! They’re finished – I was waiting for silver rivets to arrive before showing you. If you remember my first pair – they turned out O.K. but I couldn’t bend my knees (or much else) due to using fabric with no stretch. I made these ones in exactly the same size but, due to using the right fabric, they fit. Who would have thunk it?
Here’s a full length pic. I wouldn’t normally wear everything so cropped on the top with skinny jeans but, as this is all about the jeans, I wanted to show you them properly.
I probably wouldn’t normally wear skinny jeans with heels either but, because the pattern on this denim is so ‘extravagant’, I probably could ‘posh them up’ with a dressy top and heels. Just thinking aloud here.
A few close ups of jeans laid flat so you don’t have to study my nether regions too much to see the details.
The silver rivets were ordered from Japan as I couldn’t find them anywhere else and wanted them to go with the silvery grey pattern and the top stitch thread I used. I was quite pleased with my top stitching overall and I managed to hide a bit of a ‘wobble’ on the waistband with one of the belt loops.
I did a simple design on the pockets and stressed for a long time about where to place them. Apparently pocket placement is a big deal with jeans. How close should they be to the centre seam and the yoke, what angle of slant should there be, how high or low to place them – apparently all make a difference to the way your derrière will present itself to observers (should there be any). In the end though, I pinned them on in the position I thought would be right but nearly did myself an injury twisting round to look at my own denim clad bottom in the mirror – Mr. Tialys being unavailable for comment – so on they went for better or worse.
I don’t think I’m being unreasonable when I say I’m excited by a coin pocket.
I’m wearing a belt, mainly because my jeans button is, unfortunately, half an inch too far in from the edge. This is one of the two things that have made these jeans less than perfect – there’s always something isn’t there? My sewing machine couldn’t manage its one step buttonhole function because of the multiple layers of fabric at the edge of the waistband so would stop mid-buttonhole. I had to unpick it about three times and the fabric started showing signs of damage in that spot. In the end, I resorted to the four step buttonhole on my very basic Singer machine (not my 1950s one) and subsequently remembered I had to do exactly the same thing with my first pair. Shame I didn’t remember earlier. It worked but I had to position it where the unpicking had happened to hide it so a belt will probably be the order of the day.
Since then, I’ve heard about a gadget called a ‘buttonhole height compensation plate’ which apparently solves such a problem. I had a quick look – they’re only cheap – I just need to check if I can get one compatible with my Janome. Because, yes, I’m going to make more jeans.
The second thing to moan about is that I have leg twist. The inseam is trying to twist itself round on to the front of my leg at calf level. Apparently this is very common – even with high end ready-to-wear jeans – especially the skinny ones. The pattern I used was Closet Case’s Ginger Jeans and Heather has you lay out the pattern pieces for the legs in a way that attempts to avoid this happening. That is, the legs are cut out from a single layer of fabric and the front and back legs are laid on the fabric in different directions. Or, in Heather’s words ‘to help prevent leg twist, the best way to layout your pieces is front leg, back leg, front leg turned 180 degrees, back leg turned 180 degrees (make sure these last two are also flipped wrong side up so you’re not cutting the same leg twice!) I cut mine out on a double layer 🙄 and couldn’t turn the leg pattern pieces because it would have meant the design on my jeans doing a different thing on each leg.
As I usually wear skinny jeans with boots, here’s a couple with me wearing the jeans ‘booted up’. It’s usually too hot to wear jeans in the Summer here but I think they’d look fine with sandals too.
And just to prove I can bend my knees this time…….
Now I’ve got the fit right with the Ginger Jeans which is an excellent pattern, by the way, with a very useful sewalong on the Closet Case blog, I will definitely make more pairs, but thought I’d make some more traditional jeans next with rigid denim (i.e. no stretch) in indigo and gold top stitching which, of course, will be much more visible so has to be perfect. I’ve ordered the new(ish) Dawn Jeans pattern by Megan Nielsen and will try to source the perfect denim to make them. Of course, the fitting issues will be different so another challenge but, hey, sewing projects would get boring if everything was too easy wouldn’t it?
administering medicine to cat, buttonhole height compensation plate, closet case pattern, ginger cat, ginger jeans, handmade skinny jeans, hypertension in cats, making jeans, marmalade cat, stretch jeans
Dog Collars and Bandanas
- Tight Lipped Tuesday #28
- Sunday Snow
- Scrapping Scraps
- Talking About ‘Stuff’ – A Moving Story With Some Welcome Diversions
- Keeping On The Right Side Of The Law
- Scraphappy and a Half July
- Two Wooly Collie Crosses
- Scraphappy (birth)Day – June
- Tight Lipped Tuesday #27
- Pooch Portrait Gallery
- Tight Lipped Tuesday #26
- ScrapHappy May
- Stockpiling Summer Dresses in Lockdown
- A Wren’s Nest
- Getting Cross With Cross Stitch
- Arts and Crafts
- Crochet Projects
- Dressmaking Projects
- Excuses Not to do the Housework
- freehand machine embroidery
- Interesting Vintage Finds
- Knitting Projects
- Liberty Hatbox Project
- Life in France
- Life in General
- Miscellaneous Crafts
- needle felting
- Patchwork and Quilting Projects – General
- Pets & Problems